![]() You can compare the current period with historical periods using lags report. Used to save historical values to compare with the forecast line in the next periods. Available for Standard or Standard DRP reports only. Allows forecast relocation of converted lines without a unit forecast. Used to copy a report's Forecast to another location. This feature is similar to the Data Adjust feature inside the Forecast Method tab. Used to make adjustments to the forecasted values after they have been generated. For additional information see the On-Fly Rebalance section in the Group By Tab. On-Fly Rebalance is only enabled if the currently selected workbook contains a report that supports On the fly rebalancing. Used to rebalance the hierarchy of a group forecast after the report has been generated without the need to create a new report. Note: This feature is only available in ForecastX. This option can be used to perform the “What if” inventory analysis within the Adjusted Forecast and Safety Stock features. Used to recalculate DRP based on changes made to the forecast. This button is always enabled, and it is used to run the ForecastX. The following table details what each feature means. The ForecastX toolbar appears in Microsoft Excel. In the File Selection window, go to the location where you installed ForecastX. ![]() If the ForecastXToolbar Add-In is unavailable in the list, click Browse.For previous versions of Excel, go to Tools > Add-Ins. Go back to the Excel Options Window, select Add-ins from the pane in the left, select Excel Add-ins from the menu next to Manage text, and click Go.In the Trusted Publishers tab, make sure the Trust all installed add- ins and templates option is enabled. For previous versions of Excel: Go to Tools > Macro > Security. Make sure the following checkboxes are disabled: Require Application Add-ins to be signed by Trusted Publisher and Disable all Application Add-ins. Click Trust Center in the left pane and click Trust Center Settings.Thereafter, select Wizard.Connect Friendly Name from the list, enable the checkbox next to it, and click OK. Note: If not, select Com Add-Ins from the Manage menu. Ensure ForecastX is listed under Active Application Add-ins.In the menu next to the Manage option, select Excel Add-ins and click Go.Select Add-ins from the left-hand pane.If you are using Microsoft Excel 2007, click on the top left corner and select Excel.Note: If you are using Microsoft Excel 2007, go to step 2. If you are using Microsoft Excel 2003 or previous versions, click Tools > Add-Ins from the Excel toolbar.Also, if ForecastX is displaying in Excel but none of the buttons work, and nothing happens when the toolbar buttons are clicked, you need to enable the COM add-in. ![]() If you do not see the ForecastX on the toolbar, you may have to enable the ForecastX in Excel. Over an average June, swells large enough to cause clean enough to surf waves at Centre Crack run for about 20% of the time.To ensure that the ForecastX™ has been installed successfully, you can access ForecastX by going to Start > All Programs > Microsoft Office > Microsoft Office Excel. Because wind determines whether or not waves are good for surfing at Centre Crack, you can view an alternative image that shows only the swells that were predicted to coincide with glassy or offshore wind conditions. To keep it simple we don't show these in the rose diagram. We group these with the no surf category of the bar chart. Because the wave model grid is out to sea, sometimes a strong offshore wind blows largest waves away from Centre Crack and offshore. The diagram indicates that the prevailing swell direction, shown by the biggest spokes, was SW, whereas the the most common wind blows from the NW. In either graph, the area of any colour is proportional to how often that size swell happens. Green and yellow show increasing swell sizes and largest swells greater than >3m (>10ft) are shown in red. Blue shows the smallest swells, less that 0.5m (1.5 feet) high. Five colours illustrate increasing wave sizes. The rose diagram describes the distribution of swell sizes and swell direction, while the graph at the bottom shows the same thing but without direction information. The wave model does not forecast wind or surf right at the coast so we have chosen the most applicable grid node based on what we know about Centre Crack, and at Centre Crack the best grid node is 13 km away (8 miles). The rose diagram illustrates the range of swells directed at Centre Crack through a typical June and is based upon 3266 NWW3 model predictions since 2006 (values every 3 hours).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |